Engine:
Full engine disassembly, inspection, assembly, tuning, and troubleshooting (including valve adjustment, timing chain, oil system, cooling system if applicable)
Transmission:
Gearbox (6-speed), clutch, final drive (Paralever system) inspection, repair, and maintenance.
Brakes:
ABS II, integral ABS, hydraulic system, calipers, discs, fluid replacement, bleeding procedures.
Electrical:
Complete wiring diagrams, component testing, charging system (alternator, voltage regulator), ignition system, lighting, instrumentation, starter motor, battery.
Suspension:
Front Telelever system, rear Monolever system (single-sided swingarm), shock absorbers, fork seals, bearings, adjustments.
Fuel System:
Fuel injection (Motronic MA 2.4/MA 2.5), fuel pump, injectors, throttle body, fuel tank, fuel lines.
Exhaust System:
Catalytic converter, muffler, lambda sensors, exhaust gaskets, leak detection.
Frame And Body:
Chassis, subframe, fairings, body panels, seats, luggage systems, center stand, side stand.
Wheels And Tires:
Wheel bearing replacement, tire mounting and balancing, spoke tensioning (if applicable).
Controls:
Throttle control, clutch lever, brake levers, handlebar controls, foot controls.
Maintenance:
Scheduled maintenance, oil changes, filter replacements (oil, air, fuel), spark plug replacement, brake fluid changes, coolant flushes (if applicable), lubrication points.
Repair:
Detailed step-by-step repair instructions for all major components and systems, including component removal, installation, and adjustment.
Troubleshooting:
Diagnostic flowcharts, symptom-based troubleshooting guides, common fault identification and resolution.
Rebuild:
Complete engine rebuild procedures, gearbox overhaul, suspension component rebuilding.
Technical Data:
Torque specifications, clearance measurements, adjustment procedures, diagnostic trouble codes (DTCs).
Bodywork Repair:
Fairing removal/installation, panel alignment, seat adjustments, luggage system servicing.
Electrical Diagnostics:
Detailed wiring diagrams, troubleshooting for common electrical faults using multimeters and diagnostic tools.
Fuel System Cleaning:
Instructions for cleaning fuel injectors, throttle bodies, and fuel filters.
Suspension Adjustment:
Preload and damping adjustments for front and rear suspension.
Chassis Maintenance:
Wheel bearing checks and replacement, steering head bearing service, swingarm bearing inspection.
Depth:
In-depth, covering all aspects from basic maintenance to complete engine rebuilds and advanced diagnostics.
Engine Type:
Four-stroke, two-cylinder, boxer-twin, air/oil-cooled
Displacement:
1130 cc (69 cu in)
Bore X Stroke:
98 mm x 74.5 mm (3.86 in x 2.93 in)
Compression Ratio:
10.0:1
Horsepower:
95 hp (70 kW) @ 7250 rpm (approx.)
Torque:
98 Nm (72 lb-ft) @ 5250 rpm (approx.)
Fuel Delivery:
Electronic Fuel Injection (EFI) - Bosch Motronic MA 2.4/MA 2.5
Fuel Type:
Unleaded gasoline, 91 octane (95 RON) or higher recommended
Ignition Type:
Digital Electronic Ignition (CDI)
Cooling Method:
Air-cooled with oil cooling for the cylinder heads
Oil Change Interval:
Every 10,000 km (6,000 miles) or annually.
Valve Adjustment Interval:
Every 20,000 km (12,000 miles) or as needed based on inspection.
Brake Fluid Change:
Every 2 years.
Engine Oil Type:
SAE 20W-40 or SAE 15W-40 API SG or higher.
Engine Oil Capacity:
Approx. 4.0 liters (4.2 US quarts) without filter change, 4.25 liters (4.5 US quarts) with filter change.
Gearbox Oil Type:
SAE 75W-90 GL-5 gear oil.
Final Drive Oil Type:
SAE 75W-90 GL-5 gear oil.
Brake Fluid Type:
DOT 4 brake fluid.
Common Problems:
Potential for wear on the spline shaft (final drive), occasional issues with the ABS modulator, clutch slave cylinder leaks, alternator output degradation, and voltage regulator failures.