Engine Mechanical:
Rotary engine (12A) disassembly, assembly, inspection, overhaul
Fuel System:
Carburetor (various models), fuel pump, fuel lines, fuel tank
Ignition System:
Distributor, ignition coils, spark plugs, wiring
Cooling System:
Radiator, water pump, thermostat, hoses, fan
Lubrication System:
Oil pump, oil filter, oil passages, oil requirements
Exhaust System:
Exhaust manifold, pipes, muffler, catalytic converter (where applicable)
Transmission Manual:
Clutch, gearbox (4-speed and 5-speed) disassembly, assembly, adjustments
Transmission Automatic:
Automatic transmission (optional) service and adjustments
Driveline:
Propeller shaft, differential, drive axles
Suspension Front:
MacPherson struts, control arms, bushings, springs, shock absorbers
Suspension Rear:
Leaf springs, shock absorbers, locating links (depending on body style)
Steering System:
Steering box, steering column, tie rods, linkages
Brake System:
Front disc brakes, rear drum brakes, master cylinder, brake lines, calipers, wheel cylinders
Electrical System:
Battery, alternator, starter motor, lighting, gauges, wiring diagrams
Body And Chassis:
Body panel removal/installation, frame components, weatherstripping
Interior:
Seating, dashboard, trim panels, carpets, headliner
Heating And Ventilation:
HVAC system components, blower motor, heater core, A/C (if equipped)
Exterior:
Bumpers, grille, doors, hood, trunk lid, glass, trim
Routine Maintenance:
Oil changes, filter replacements, spark plug checks, fluid level checks
Engine Overhaul:
Complete engine rebuild procedures for the 12A rotary engine
Transmission Repair:
Gearbox disassembly, reassembly, synchro ring replacement, bearing service
Suspension Diagnosis And Repair:
Wheel bearing replacement, strut replacement, bushing renewal
Brake Service:
Pad/shoe replacement, caliper/wheel cylinder overhaul, bleeding procedure
Electrical Troubleshooting:
Diagnostic procedures for common electrical faults, wiring harness repair
Carburetor Adjustment And Rebuild:
Detailed procedures for setting idle speed, mixture, and rebuilding carburetor units
Rotary Apex Seal Inspection:
Procedures for assessing apex seal wear and potential replacement
Cooling System Flush And Refill:
Proper procedures for draining, flushing, and refilling the cooling system
Ignition Timing Adjustment:
Setting ignition timing using a timing light
Wheel Alignment Specifications:
Front and rear wheel alignment angles
Troubleshooting Guides:
Step-by-step diagnostics for common issues
Depth:
Complete factory-level repair and overhaul information
Detail Level:
Hundreds of photos and illustrations, detailed substeps, notes, cautions, warnings
Diagnostic Tools:
Information on basic diagnostic tools and techniques required
Oil Change Interval:
Typically every 3,000 miles or 3 months (check manual for specific year/model)
Spark Plug Replacement:
Every 15,000 - 20,000 miles (special rotary spark plugs)
Coolant Flush:
Every 2 years or 24,000 miles
Engine Oil Viscosity:
SAE 20W-50 or specialized rotary oil (refer to manual)
Coolant:
Ethylene glycol-based antifreeze (50/50 mix with distilled water)
Brake Fluid:
DOT 3 or DOT 4 (refer to manual)
Transmission Fluid Manual:
GL-4 Gear Oil (e.g., SAE 80W-90)
Transmission Fluid Automatic:
Dexron II or equivalent (refer to manual)
Rotary Engine:
Apex seal wear, oil seal failure, carbon buildup, potential for oil injection system issues
Carburetor:
Tuning difficulties, vacuum leaks, float level adjustments
Cooling System:
Hose degradation, radiator leaks, thermostat failures
Suspension:
Bushings wear, strut mount issues, ball joint wear
Electrical:
Corroded wiring, alternator issues, starter motor wear
