Engine:
Internal combustion engine assembly, disassembly, inspection, repair, cooling system, lubrication system, fuel delivery, ignition system, exhaust system.
Transmission:
CVT (Continuously Variable Transmission) system, clutch operation, belt inspection and replacement, gearbox lubrication and maintenance.
Drivetrain:
Front and rear driveshafts, differential assemblies, final drive, axle components, U-joints.
Suspension:
Front and rear suspension components, shock absorbers, A-arms, bushings, steering knuckles, alignment specifications.
Brakes:
Hydraulic brake system, brake calipers, master cylinder, brake lines, brake pads, rotor inspection and replacement, bleeding procedures.
Steering:
Steering column, tie rods, ball joints, steering linkage, potential mention of electronic power steering if applicable to the model/year.
Electrical:
Battery system, charging system (stator, regulator/rectifier), starter motor, lighting system (headlights, taillights, brake lights), ignition switch, wiring diagrams, fuses, relays.
Bodywork:
Body panels, fenders, racks, seat, handlebars, plastics, fairings, fasteners.
Cooling System:
Radiator, fan, coolant, thermostat, hoses, water pump.
Fuel System:
Fuel tank, fuel pump, fuel lines, fuel filter, carburetor or fuel injection system (depending on specific 400 TRV configuration).
Lubrication System:
Oil pump, oil filter, oil passages, oil capacity and type.
Routine Maintenance:
Oil change, filter replacement, air filter cleaning/replacement, spark plug inspection/replacement, drive belt inspection, chain lubrication (if applicable), tire pressure checks, brake fluid checks, battery maintenance.
Troubleshooting:
Diagnostic charts, symptom-based troubleshooting, common fault identification for electrical, engine, and mechanical issues.
Repair Procedures:
Step-by-step instructions for disassembly, repair, and reassembly of all major components and systems.
Component Replacement:
Detailed guidance on replacing wear items and faulty components such as brake pads, bearings, seals, cables, and electronic sensors.
Engine Rebuild:
Comprehensive instructions for complete engine overhaul, including piston, ring, cylinder, valve train, and crankshaft servicing.
Transmission Overhaul:
Procedures for gearbox internal inspection, bearing replacement, seal replacement, and clutch assembly servicing.
Electrical Diagnostics:
Wiring diagrams, circuit testing, component testing, and fault finding for the electrical system.
Suspension Adjustment:
Guidance on adjusting suspension settings, servicing shock absorbers, and replacing suspension wear components.
Wheel Alignment:
Specifications and procedures for checking and adjusting wheel alignment (toe-in/toe-out).
Depth:
Comprehensive factory-level detail, suitable for professional technicians and advanced DIY enthusiasts.
Diagnostics:
Advanced diagnostic procedures, including interpretation of diagnostic codes (if applicable) and troubleshooting of complex systems.
Specifications:
Detailed torque specifications, clearance measurements, fluid capacities, electrical resistance values, and performance data.
Diagrams:
Exploded views of components, system diagrams, and detailed wiring schematics.
Manufacturer:
Arctic Cat (likely using a Loncin or similar manufactured engine, common for this class)
Configuration:
Single-cylinder, 4-stroke
Displacement:
Approximately 375cc - 400cc (exact specification may vary slightly by sub-model, but '400' is indicative)
Cooling System:
Liquid-cooled
Horsepower:
Estimated 25-30 HP (typical for this engine displacement and class)
Torque:
Estimated 20-25 lb-ft (typical for this engine displacement and class)
Fuel Delivery:
Likely Carbureted (e.g., Mikuni, Keihin) or potentially early fuel injection for 2007, depending on specific trim/market.
Fuel Type:
Unleaded gasoline (Octane rating typically 87 or higher)
Oil Type:
API SG or higher, SAE 10W-40 (common for ATVs, confirm with manual)
Oil Capacity:
Approximately 1.7 - 2.0 liters (check manual for exact capacity with filter change)
Length:
Approx. 83 inches (2108 mm) (typical for this class, verify specific model)
Width:
Approx. 46 inches (1168 mm) (typical for this class, verify specific model)
Height:
Approx. 47 inches (1194 mm) (typical for this class, verify specific model)
Dry Weight:
Approx. 600-650 lbs (272-295 kg) (typical for this class, verify specific model)
Ground Clearance:
Approx. 8-10 inches (203-254 mm) (typical for this class, verify specific model)
Front Rack Capacity:
Approx. 100 lbs (45 kg) (typical)
Rear Rack Capacity:
Approx. 200 lbs (90 kg) (typical)
Towing Capacity:
Approx. 1050 lbs (476 kg) (typical)
Front Tire Size:
e.g., 25x8-12 (verify specific model)
Rear Tire Size:
e.g., 25x10-12 (verify specific model)
Wheel Bolt Pattern:
Likely 4x110mm or similar standard ATV pattern (verify with manual)
Engine Oil Change:
Every 100 hours or annually (verify with manual for precise intervals).
Air Filter Cleaning:
Every 25 hours or as needed based on conditions.
Spark Plug Replacement:
Every 100 hours or annually.
Drive Belt Inspection:
Every 50 hours or annually, replace as needed.
Brake Fluid Flush:
Every 2 years or as recommended.
Engine Oil Spec:
SAE 10W-40, API SG or higher.
Coolant Spec:
Ethylene glycol-based antifreeze (50/50 mix with distilled water), typically green or yellow (verify with manual).
Brake Fluid Spec:
DOT 3 or DOT 4 hydraulic brake fluid (verify with manual).
Gearbox Oil Spec:
Specific gear oil or SAE 80W-90 (verify with manual).
Common Wear Items:
Drive belts, brake pads, suspension bushings, wheel bearings, tie rod ends.
Electrical Concerns:
Occasional issues with stator, regulator/rectifier, or battery connections; wiring harness integrity.
Engine Performance:
Carburetor tuning/cleaning, potential issues with starter solenoids or ignition coils.
