Engine Mechanical:
        
        
            Complete engine overhaul, top end, bottom end, pistons, rings, valves, camshafts, timing, lubrication system, cooling system (if applicable).
        
     
    
        
            Fuel System:
        
        
            Carburetor tuning and rebuild, fuel injection system (if applicable), fuel pump, fuel lines, fuel tank.
        
     
    
        
            Ignition System:
        
        
            Spark plugs, ignition coils, ignition control module, timing.
        
     
    
        
            Transmission:
        
        
            Clutch operation and adjustment, gear shifting mechanisms, transmission case, internal components, lubrication.
        
     
    
        
            Drivetrain:
        
        
            Belt drive system, primary drive, final drive, wheel bearings, drive sprocket, driven sprocket.
        
     
    
        
            Suspension:
        
        
            Front forks (telescopic, inverted types), rear shock absorbers, linkages, bushings, seals, adjustments.
        
     
    
        
            Braking System:
        
        
            Front and rear brake calipers, master cylinders, brake lines, brake pads, brake discs, bleeding procedures, parking brake.
        
     
    
        
            Electrical System:
        
        
            Battery, charging system (alternator, regulator/rectifier), starter motor, lighting (headlight, taillight, turn signals), wiring diagrams, fuses, relays, switches, diagnostics.
        
     
    
        
            Frame And Bodywork:
        
        
            Frame inspection, body panel removal and installation, fenders, fuel tank, seat, handlebars, controls.
        
     
    
        
            Wheels And Tires:
        
        
            Wheel removal and installation, tire mounting and balancing, spoke tension, valve stem replacement.
        
     
    
    
        
            Preventative Maintenance:
        
        
            Scheduled maintenance checks, lubrication points, fluid changes, filter replacements, chain/belt adjustment.
        
     
    
        
            Routine Maintenance:
        
        
            Oil changes, filter replacements, spark plug service, air filter cleaning/replacement, brake fluid flush.
        
     
    
        
            Troubleshooting:
        
        
            Diagnostic charts, common problem identification and solutions for engine, electrical, and mechanical systems.
        
     
    
        
            Repair Procedures:
        
        
            Step-by-step instructions for component removal, disassembly, inspection, repair, and reassembly.
        
     
    
        
            Rebuilds:
        
        
            Detailed instructions for engine, transmission, and carburetor rebuilds.
        
     
    
        
            Electrical Diagnostics:
        
        
            Wiring diagrams, component testing, fault finding for electrical issues.
        
     
    
        
            Specification Data:
        
        
            Torque specifications, clearances, fluid capacities, electrical specifications.
        
     
    
    
        
            Depth:
        
        
            Comprehensive, from basic rider maintenance to full engine and component overhauls.
        
     
    
        
            Diagnostic Capabilities:
        
        
            Advanced diagnostic procedures and troubleshooting guides.
        
     
    
        
            Component Level Detail:
        
        
            Detailed breakdown of individual components and their service requirements.
        
     
 
    
    
    
        
            Engine Family:
        
        
            Harley-Davidson Evolution (Big Twin)
        
     
    
        
            Engine Type:
        
        
            Air-cooled, 45-degree V-twin
        
     
    
        
            Displacement:
        
        
            1450cc (88 cubic inches)
        
     
    
        
            Bore X Stroke:
        
        
            3.75 in x 4.00 in (95.25 mm x 101.6 mm)
        
     
    
        
            Compression Ratio:
        
        
            8.8:1 (typical)
        
     
    
        
            Valvetrain:
        
        
            Overhead valves (OHV), 2 valves per cylinder, pushrod actuated.
        
     
    
    
        
            Horsepower Est:
        
        
            ~60-65 HP @ 5000 RPM (approximate, varies by tuning)
        
     
    
        
            Torque Est:
        
        
            ~75-80 lb-ft @ 3000 RPM (approximate, varies by tuning)
        
     
    
    
        
            Carburetion:
        
        
            Keihin CV (Constant Velocity) 40mm carburetor (standard for most models in this range).
        
     
    
        
            Fuel Type:
        
        
            Unleaded gasoline, 87 octane or higher.
        
     
 
    
    
    
        
            Oil Change:
        
        
            Every 2,500-5,000 miles or annually, depending on usage and oil type.
        
     
    
        
            Primary Chain Tension:
        
        
            Check at 1,000 miles and then every 5,000 miles.
        
     
    
        
            Spark Plugs:
        
        
            Replace every 10,000-20,000 miles (depending on plug type).
        
     
    
        
            Belt Drive Inspection:
        
        
            Inspect for wear and tension at regular intervals (e.g., 5,000 miles).
        
     
    
    
        
            Engine Oil:
        
        
            Harley-Davidson 20W50 motorcycle oil (or equivalent API CI-4/SJ or higher).
        
     
    
        
            Primary Chain Case Oil:
        
        
            Harley-Davidson primary chain case lubricant, or SAE 75W/90 gear oil (API GL-4).
        
     
    
        
            Transmission Oil:
        
        
            Harley-Davidson transmission fluid, or SAE 75W/90 gear oil (API GL-5).
        
     
    
        
            Brake Fluid:
        
        
            DOT 4 brake fluid.
        
     
    
        
            Fork Oil:
        
        
            Specific weight oil (e.g., 10W or 15W) as per manual, capacity varies by fork type.
        
     
    
    
        
            Cam Chain Tensioners:
        
        
            Early Twin Cam engines (pre-2007) were known to have issues with cam chain tensioners wearing out, potentially leading to engine damage. This manual would detail inspection and replacement procedures.
        
     
    
        
            Rear Cylinder Overheating:
        
        
            Air-cooled V-twins can experience increased heat in the rear cylinder, especially in hot weather or stop-and-go traffic. Proper lean mixture and maintenance are crucial.
        
     
    
        
            Carburetor Tuning:
        
        
            CV carburetors can require periodic adjustment for optimal performance and fuel economy.
        
     
    
        
            Electrical Connections:
        
        
            Vibrations can sometimes lead to loose electrical connections or corrosion, requiring inspection and tightening.
        
     
 
    
    
    
        
            Heritage:
        
        
            Harley-Davidson has a long-standing reputation for building iconic American motorcycles with a focus on rider experience and a distinctive sound and style.
        
     
    
    
        
            Dyna Platform Introduction:
        
        
            The Dyna platform was introduced in 1991, evolving from earlier Big Twin models with a focus on improved handling and a more modern riding experience. The Wide Glide variant is characterized by its raked-out front end and extended forks, reminiscent of classic chopper styling.
        
     
    
        
            Fxwdg Specifics:
        
        
            The FXDWG Dyna Wide Glide combines the classic 'chopper' aesthetic with the Dyna chassis. Throughout the covered years (1999-2005), the model received evolutionary updates, particularly in the engine and braking systems, and refinements to suspension and electrical components.
        
     
    
    
        
            Manufacturing Location:
        
        
            United States
        
     
    
        
            Production Period Covered:
        
        
            1999-2005