Engine Systems:
Fuel System, Ignition System, Lubrication System, Engine Disassembly/Reassembly, Cooling System (Implied)
Drivetrain Systems:
Transmission (Disassembly/Reassembly, Overhaul), Clutch System (Implied), Drive Axles (Implied)
Chassis Systems:
Braking System, Suspension System, Steering System, Exhaust System
Electrical Systems:
Wiring Diagrams, Lighting, Starting & Charging, Ignition System, Electronic Control Units (Implied)
Body Systems:
Body Panels, Doors, Interior Trim, Exterior Trim, Sealing
Cooling System:
Radiator, thermostat, water pump, hoses, coolant flow
Clutch System:
Clutch disc, pressure plate, release bearing, hydraulic system (for manual transmission)
Suspension System:
Front and rear suspension components, shock absorbers, springs, bushings
Steering System:
Steering rack, tie rods, power steering system (if equipped)
Braking System:
Front and rear brakes (discs/drums), hydraulic system, parking brake
Fuel System Details:
Fuel pump, injectors, fuel filter, fuel tank, evaporative emission control system
Ignition System Details:
Ignition coils, spark plugs, distributor (if applicable), ignition timing
Lubrication System Details:
Oil pump, oil filter, oil passages, oil pressure
Electrical System Details:
Battery, starter motor, alternator, lighting circuits, accessory circuits, fuses, relays, ECU diagnostics
Body Repair:
Procedures for body panel repair, dent removal, and potentially rust repair guidance.
Interior Trim:
Information on the removal and installation of interior trim components for access to underlying systems.
Maintenance Procedures:
Routine Maintenance, Tune-ups, Fluid Changes, Filter Replacements
Repair Procedures:
Component Removal & Installation, Overhaul of Major Assemblies, Diagnostic Procedures
Troubleshooting:
Diagnostic flowcharts, symptom-based troubleshooting guides
Technical Bulletins References:
Incorporates instructions for proprietary components from respective manufacturers, implying access to manufacturer-specific data.
Diagnostic Codes:
Procedures for reading and interpreting diagnostic trouble codes (DTCs) if the vehicle is equipped with OBD-II or similar diagnostic systems.
Torque Specifications:
Precise torque values for critical fasteners to ensure proper assembly and prevent damage.
Special Tools:
Identification and usage instructions for special tools recommended or required for specific repair procedures.
Depth Of Information:
Detailed repair and overhaul procedures, including engine and transmission disassembly, proprietary component instructions
Rebuild Procedures:
Detailed instructions for complete engine and transmission rebuilds, including component measurements and specifications.
Oil Change Interval Engine:
Every 5,000 - 10,000 km or 6-12 months (refer to manual for precise interval)
Air Filter Replacement Interval:
Every 20,000 - 30,000 km or as needed based on driving conditions
Spark Plug Replacement Interval:
Every 40,000 - 60,000 km (depending on spark plug type)
Engine Oil Specification:
API SG or higher, Viscosity: 0W-20, 5W-30, or 10W-30 (refer to manual for specific viscosity recommendation based on climate)
Coolant Specification:
Ethylene Glycol based coolant, typically a 50/50 mix with distilled water
Brake Fluid Specification:
DOT 3 or DOT 4
Transmission Fluid Manual:
API GL-4, SAE 75W-90 Gear Oil (typical)
Transmission Fluid Automatic:
Dexron III or equivalent (check manual for exact specification)
Common Issues Vehicle:
Potential for rust on body panels, wear on suspension components due to age, potential for minor electrical issues, aging rubber components (hoses, seals)
Manual Benefit For Issues:
Provides diagnostic and repair procedures to address common and uncommon issues.
Maintenance Schedule Emphasis:
The manual emphasizes routine maintenance to prevent issues and prolong the vehicle's life.
Daihatsu Heritage:
Daihatsu has a long history of producing small, economical vehicles, particularly Kei cars for the Japanese market.
Cuore Generation Context:
The L701 represents a generation of the Cuore model, known for its compact size and practicality.
Cuore Key Attributes:
Known for its compact size, fuel efficiency, and affordability, making it a popular city car.
Production Location Typical:
Japan (primary manufacturing)
