Manual Coverage
|
Systems Covered
|
Engine Overhaul:
|
Complete disassembly, inspection, repair, and reassembly procedures for the 125cc two-stroke engine.
|
Cooling System:
|
Radiator, hoses, thermostat, coolant specifications, bleeding procedures.
|
Fuel System:
|
Carburetor identification, adjustment, disassembly, cleaning, jetting, fuel pump (if applicable), fuel tank, fuel lines.
|
Ignition System:
|
CDI unit, spark plug specifications, ignition timing, stator, coil testing.
|
Exhaust System:
|
Exhaust pipe, silencer maintenance, packing replacement.
|
Transmission And Drivetrain:
|
Clutch assembly, gearbox disassembly/reassembly, gear inspection, chain and sprocket maintenance, lubrication.
|
Suspension Front:
|
Front fork disassembly, seal replacement, oil type and level, damping adjustments, spring preload.
|
Suspension Rear:
|
Monoshock absorber, linkage system, bearing maintenance, shock oil, gas pressure, spring adjustments.
|
Braking System Front:
|
Brake caliper, master cylinder, brake lines, brake pads, rotor inspection and replacement, fluid specifications, bleeding.
|
Braking System Rear:
|
Rear brake caliper, master cylinder, brake lines, brake pads, rotor inspection and replacement, fluid specifications, bleeding.
|
Wheels And Tires:
|
Wheel bearing maintenance, spoke tension, tire pressure recommendations, tire replacement.
|
Electrical System:
|
Wiring diagrams, lighting system, battery maintenance, fuse locations, switch operation.
|
Frame And Bodywork:
|
Frame inspection, subframe, plastic body panel removal/installation, seat, fuel tank mounting.
|
Procedures Included
|
Routine Maintenance:
|
Oil changes, filter replacement, chain lubrication, air filter cleaning/replacement, spark plug checks, brake checks.
|
Troubleshooting:
|
Diagnostic charts for common problems, symptoms, and solutions.
|
Engine Repair:
|
Piston and cylinder inspection/replacement, crankshaft and connecting rod service, valve clearance (if applicable, though unlikely for 125 2T), reed valve inspection.
|
Suspension Rebuild:
|
Detailed steps for fork seal replacement, shock absorber servicing.
|
Electrical Diagnostics:
|
Testing of charging system, ignition components, and lighting circuits.
|
Clutch Adjustment And Service:
|
Cable adjustment, clutch plate replacement.
|
Carburetor Tuning:
|
Jetting recommendations for different altitudes and conditions, idle speed adjustment.
|
Technical Depth
|
Diagnostic Information:
|
Includes specifications for measurements, tolerances, and test procedures.
|
Repair Procedures:
|
Step-by-step instructions with diagrams for most mechanical and electrical repairs.
|
Technical Specifications:
|
Torque values, clearances, fluid capacities, electrical specifications.
|
Parts Identification:
|
Likely includes part numbers and exploded views for component identification (though not a dedicated parts catalog).
|
Maintenance
|
Service Intervals
|
Oil Change Interval:
|
Transmission oil: Recommended every 10-15 hours of riding or annually (verify in manual).
|
Air Filter Cleaning:
|
Recommended after every few rides, depending on conditions.
|
Spark Plug Replacement:
|
Check and clean every 10-15 hours, replace as needed (refer to manual for specific type).
|
Chain And Sprocket Inspection:
|
Check tension and wear before every ride; lubricate frequently.
|
Fluid Specifications
|
Coolant Type:
|
Ethylene Glycol based coolant with corrosion inhibitors (specific type and mix ratio in manual).
|
Brake Fluid Type:
|
DOT 4 Hydraulic Brake Fluid (verify in manual).
|
Known Issues
|
Clutch Wear:
|
Common in 125cc two-strokes with aggressive riding; clutch plates may require replacement sooner than expected.
|
Carburetor Tuning Sensitivity:
|
Two-stroke carburetors can be sensitive to altitude and temperature changes, requiring frequent jetting adjustments for optimal performance.
|
Power Valve Maintenance:
|
The exhaust power valve system requires regular cleaning and lubrication to prevent sticking and ensure proper operation.
|