Engine:
Complete engine disassembly, assembly, tuning, and diagnostics
Fuel System:
Fuel injection, throttle bodies, fuel pump, injectors, fuel tank, lines
Ignition System:
Spark plugs, coils, ECU control, timing
Exhaust System:
Exhaust manifolds, catalytic converters, mufflers, emissions control
Cooling System:
Radiator, coolant, water pump, thermostat, fan control
Transmission:
Clutch operation, gearbox inspection, maintenance, and repair
Chassis Frame:
Frame inspection, structural integrity, mounting points
Suspension Front:
Fork disassembly, seal replacement, oil levels, valving, damping adjustments
Suspension Rear:
Monoshock, linkage inspection, rear shock absorber service, spring preload, rebound adjustment
Brakes Front:
Brake caliper service, pad replacement, disc inspection, master cylinder, hydraulic lines
Brakes Rear:
Brake caliper service, pad replacement, disc inspection, master cylinder, hydraulic lines
Wheels Tires:
Wheel bearing service, tire mounting, balancing, wheel specifications
Electrical System:
Wiring diagrams, battery, charging system, starter, lighting, fuses, relays
Electronics ECU:
ECU diagnostics, sensor testing, communication protocols
Bodywork Panels:
Fairing removal and installation, seat, fuel tank cover, panel fasteners
Controls:
Throttle cables, clutch lever, brake levers, handlebar controls
Maintenance:
Scheduled maintenance, oil changes, filter replacements, chain adjustment, lubrication
Troubleshooting:
Diagnostic procedures, fault code interpretation, common problem resolution
Repair Overhaul:
Complete engine rebuilds, gearbox overhauls, suspension component repairs
Inspections:
Pre-ride inspections, periodic inspections of critical components
Special Tools:
Identification and usage of Aprilia-specific tools
Torque Specifications:
Precise torque values for all fasteners
Diagnostics:
Advanced electronic diagnostics, sensor calibration
Engine Rebuild:
Full engine disassembly, component measurement, rebuilding procedures
Electrical Schematics:
Detailed wiring diagrams for all systems
Suspension Tuning:
Adjustment procedures for damping and spring preload
Engine Type:
V90 twin, four-stroke
Bore X Stroke:
98 mm x 79.5 mm
Compression Ratio:
12.0:1
Valve Train:
DOHC, 4 valves per cylinder
Horsepower Peak:
Approx. 130 PS (95.6 kW) @ 8,700 rpm
Torque Peak:
Approx. 11.7 kgm (115 Nm) @ 7,000 rpm
Fuel Delivery:
Electronic fuel injection with ride-by-wire throttle control
Throttle Body Diameter:
55 mm
Fuel Type:
Unleaded gasoline, minimum 95 octane (RON)
Oil Type:
Semi-synthetic or fully synthetic motorcycle engine oil meeting API SG/SH/SJ or higher, and JASO MA/MA2 specifications
Oil Capacity Filter Change:
Approx. 3.4 liters
First Service:
Typically around 1,000 km (oil, filter, chain check, general inspection)
Major Service:
Recommended every 10,000 - 12,000 km or annually, including valve clearance checks, spark plug replacement, and detailed inspections
Oil Change Interval:
Every 5,000 - 10,000 km or annually, whichever comes first (consult manual for exact recommendation)
Engine Oil Grade:
Refer to manual for specific viscosity (e.g., 10W-40, 15W-50) and API/JASO ratings
Coolant Type:
Ethylene glycol based coolant, mix 50/50 with distilled water
Clutch Fluid:
DOT 4 (if hydraulic clutch)
Fork Oil Type:
Refer to manual for specific viscosity and grade (e.g., SAE 10W, 15W)
Common Wear Items:
Clutch plates, brake pads, tires, chain and sprockets
Potential Electrical Gremlins:
Some owners report occasional minor electrical issues, often resolved by checking connections or ECU resets. The manual would detail diagnostic procedures.
Fuel System Maintenance:
Regular fuel filter checks and injector cleaning are recommended for optimal performance.
