Market Segment:
Light-duty utility tractor, suitable for small farms, homesteads, and landscaping tasks.
Competitors:
Likely competed with models from John Deere (e.g., 100 series), Ford, Massey Ferguson, and other smaller tractor manufacturers of the era.
Features:
Compact size, maneuverability, robust construction for its class, relatively simple mechanical design for ease of maintenance.
Engine:
Disassembly, Inspection, Repair, Reassembly, Troubleshooting, Specifications
Fuel System:
Carburetor service, fuel pump, fuel lines, fuel tank maintenance
Ignition System:
Spark plugs, ignition coil, distributor service (if applicable), timing adjustments
Cooling System:
Radiator, water pump, thermostat, coolant specifications
Lubrication System:
Oil pump, oil filter, oil change procedures, oil specifications
Clutch:
Clutch disc, pressure plate, throw-out bearing inspection and replacement
Transmission:
Gearbox disassembly, repair, lubrication, shift mechanism
Drive Axles:
Differential, axle shafts, bearings
Steering System:
Steering column, tie rods, steering linkage adjustments and repair
Brake System:
Brake shoes, drums, hydraulic system maintenance, bleeding procedures
Electrical System:
Wiring diagrams, starter, generator/alternator, battery service, lighting
Hydraulic System:
Hydraulic pump, cylinders, control valves, fluid specifications (for implement lift, etc.)
Power Take Off Pto:
PTO shaft, gears, engagement mechanism
Front Axle Assembly:
Front wheel bearings, kingpins, spindle service
Rear Axle Housing:
Axle shafts, rear wheel bearings, differential service
Frame And Body:
Frame inspection, fender repair, mounting points
Operator Station:
Seat, controls, dashboard layout and service
Maintenance:
Routine maintenance, lubrication points, filter replacement, fluid checks and changes
Troubleshooting:
Diagnostic charts, common problems and solutions
Repair:
Detailed step-by-step repair instructions for all major components
Overhaul:
Complete engine and transmission overhaul procedures
Adjustment:
Carburetor, ignition timing, brake, clutch, and steering adjustments
Disassembly Assembly:
Component level disassembly and reassembly instructions
Electrical Diagnostics:
Tracing electrical faults, testing components, wiring diagram interpretation
Depth:
Comprehensive - Covers routine maintenance to complete engine and transmission rebuilds. Includes detailed diagrams and specifications for accurate repair.
Engine Make:
International Harvester (proprietary design)
Engine Type:
Gasoline, 4-stroke, air-cooled (common for this era of Cadet)
Engine Displacement:
Typically in the range of 12-16 cubic inches (e.g., approx. 200-260cc). Specifics for the 76 model may vary.
Horsepower:
Estimated 7-10 PTO horsepower, likely lower drawbar horsepower. Exact figures depend on specific engine variant.
Engine Configuration:
Single-cylinder or two-cylinder (depending on specific engine used in the '76' designation).
Governor:
Mechanical governor for stable engine speed
Carburetor Type:
Single barrel carburetor (e.g., Marvel-Schebler or Zenith)
Fuel Type:
Unleaded Gasoline
Ignition Type:
Battery and Coil ignition with distributor or magneto (depending on model year and options)
Oil Change Interval:
Typically every 50-100 operating hours or annually. Specific recommendation in manual.
Air Filter Service:
Inspect at 25-50 hour intervals, clean or replace as needed. More frequent if operating in dusty conditions.
Spark Plug Replacement:
Replace annually or every 200-300 hours. Check gap regularly.
Engine Oil:
SAE 30W HD or SAE 10W-30 (depending on ambient temperature and specific IH recommendation). Capacity approx. 1.5-2 quarts. Exact spec in manual.
Hydraulic Fluid:
IH Hy-Tran fluid or equivalent tractor hydraulic fluid for lift systems and transmission. Exact spec and capacity in manual.
Common Problems:
Wear on clutch friction plates, carburetor gumming due to infrequent use and fuel degradation, ignition system component failure (points, condenser), starter motor wear, hydraulic system leaks.
