Engine Mechanical:
Complete overhaul, diagnosis, repair procedures for all available engines
Fuel System:
Fuel injection systems, carburetors (if applicable), fuel pumps, lines, and filters
Cooling System:
Radiator, water pump, thermostat, hoses, fan, coolant specifications
Ignition System:
Spark plugs, ignition coils, distributors, timing, diagnostic procedures
Exhaust System:
Catalytic converter, mufflers, pipes, emissions controls
Transmission Manual:
Clutch, gearbox, shifting mechanisms, fluid specifications, repair
Transmission Automatic:
Torque converter, valve body, seals, fluid specifications, diagnosis, repair
Drivetrain:
Drive shafts, U-joints, differentials, axle shafts, hub bearings
Steering System:
Power steering pump, steering gear/rack, tie rods, linkages, alignment specifications
Suspension System:
Front and rear suspension components, springs, shock absorbers, ball joints, control arms, bushings
Brake System:
Brake pads, rotors, calipers, drums, wheel cylinders, master cylinder, power booster, ABS (if equipped), bleeding procedures
Electrical System:
Wiring diagrams, component testing, fuses, relays, battery, charging system, starting system
Lighting System:
Headlights, taillights, turn signals, interior lighting, bulb types and replacement
HVAC System:
Air conditioning, heating, ventilation, blower motor, climate controls, refrigerant types
Body And Frame:
Body panel removal/installation, glass replacement, door mechanisms, chassis specifications
Interior Trim:
Dashboard, door panels, seats, upholstery, trim panel removal and installation
Basic Maintenance:
Oil changes, filter replacements, fluid checks and top-offs, tire rotation
Troubleshooting:
Diagnostic flowcharts, symptom-based troubleshooting guides
Repair Procedures:
Step-by-step instructions for component removal, repair, and installation
Component Rebuild:
Detailed instructions for rebuilding engines, transmissions, carburetors, etc.
Diagnostics:
Electrical testing, mechanical testing, using diagnostic tools
Depth:
Comprehensive factory-level service and repair information
Detail Level:
Detailed specifications, torque values, clearances, diagnostic trouble codes (DTCs) if applicable
Visual Aids:
Likely includes diagrams and illustrations for procedures (based on OE material derivation)
Engine Options:
4.3L V6 (VIN Z), 5.7L V8 (VIN H), 7.4L V8 (VIN J)
4.3L V6 (Vin Z) Horsepower:
Approx. 160 hp @ 4000 rpm
4.3L V6 (Vin Z) Torque:
Approx. 230 lb-ft @ 2000 rpm
5.7L V8 (Vin H) Horsepower:
Approx. 190 hp @ 4000 rpm
5.7L V8 (Vin H) Torque:
Approx. 300 lb-ft @ 2400 rpm
7.4L V8 (Vin J) Horsepower:
Approx. 230 hp @ 3600 rpm
7.4L V8 (Vin J) Torque:
Approx. 400 lb-ft @ 2000 rpm
Fuel Delivery:
Throttle Body Injection (TBI) for 4.3L and 5.7L; TBI for 7.4L
Fuel Type:
Unleaded Gasoline
4.3L V6 Oil Capacity:
5 US quarts (4.7 L) with filter
5.7L V8 Oil Capacity:
5 US quarts (4.7 L) with filter
7.4L V8 Oil Capacity:
7 US quarts (6.6 L) with filter
Oil Change Interval:
Typically every 3,000-5,000 miles or 3-6 months, depending on driving conditions (refer to manual for specific recommendations).
Transmission Service Interval:
Automatic transmission fluid and filter change approximately every 30,000-60,000 miles. Manual transmission fluid may be a lifetime fill or specified at longer intervals (consult manual).
Coolant Change Interval:
Every 30,000-50,000 miles or 2-3 years.
Engine Oil Specification:
API Service SF or SG, SAE 10W-30 or 10W-40 (check owner's manual for specific viscosity based on temperature).
Brake Fluid Specification:
DOT 3
Power Steering Fluid:
Dexron-II (or equivalent)
Common Issues:
Potential for intake manifold gasket leaks (especially 4.3L V6), distributor housing wear, fuel pump failure, transmission hard shifting (automatic), dashboard crack/warp due to sun exposure, rear main seal leaks.