Systems Covered:
Engine, Fuel System, Ignition System, Cooling System, Lubrication System, Clutch, Transmission, Differential, Drive Axles, Steering System, Brakes, Electrical System, Hydraulics, Chassis, Bodywork, Troubleshooting, Maintenance
Page Count:
Estimated 150-250 pages (typical for this era of tractor service manuals)
Manual Type:
Workshop Service Repair Manual
Format:
PDF (Downloadable)
Engine Mechanical:
Engine overhaul, disassembly, assembly, component specifications, torques, timing, valve adjustment
Fuel System:
Carburetor service, fuel pump operation, fuel filter replacement, fuel line routing
Ignition System:
Spark plug specifications, ignition timing, distributor service, coil testing
Cooling System:
Radiator service, thermostat replacement, coolant specifications, water pump repair
Lubrication System:
Oil pump service, oil filter specifications, oil pressure testing, lubrication points
Clutch:
Clutch disc and pressure plate service, clutch adjustment, release bearing replacement
Transmission:
Gearbox disassembly and assembly, gear selection mechanisms, PTO engagement, lubrication requirements
Differential And Drive Axles:
Differential service, axle shaft removal and installation, bearing adjustments
Steering System:
Steering gearbox service, tie rod end replacement, steering linkage adjustment
Brake System:
Brake shoe replacement, drum service, brake pedal adjustment, hydraulic system bleeding
Electrical System:
Wiring diagrams, starter motor service, generator/alternator testing, battery specifications, lighting circuits
Hydraulic System:
Hydraulic pump service, cylinder repair, valve body operation, hydraulic fluid specifications, troubleshooting hydraulic lift issues
Chassis And Bodywork:
Frame inspection, fender repair, seat mounting, control lever adjustments
Routine Maintenance:
Oil changes, filter replacements, greasing points, tire pressure checks, battery maintenance
Troubleshooting:
Diagnostic charts for common problems, symptom analysis, corrective actions for engine, transmission, and hydraulic issues
Engine Rebuild:
Complete engine disassembly, cleaning, inspection, part replacement, and reassembly procedures
Transmission Overhaul:
Detailed steps for transmission disassembly, identification of worn components, and reassembly
Hydraulic System Repair:
Service procedures for hydraulic pumps, cylinders, valves, and troubleshooting lift and implement issues
Electrical Diagnostics:
Testing procedures for starter, generator, voltage regulator, and troubleshooting electrical faults using wiring diagrams
Brake System Service:
Step-by-step instructions for brake shoe replacement, drum machining, and hydraulic adjustments
Depth Of Coverage:
Comprehensive; covers detailed repair and overhaul procedures, diagnostics, and specifications for all major systems
Engine Manufacturer:
International Harvester
Engine Model Code:
Likely an IH C-series engine (e.g., C-123, C-149, or similar small displacement engine, specific to 382 model variant)
Engine Type:
4-cylinder, L-head (OHV) gasoline engine
Displacement:
Typically around 123 to 150 cubic inches (2.0L to 2.5L), specific to engine variant used in 382 model.
Horsepower Rating:
Approximate PTO horsepower of 18-25 HP (subject to specific engine and configuration)
Torque Rating:
Not typically specified in user-friendly terms for older tractors; focus on operational torque for work.
Carburetor Type:
Single barrel carburetor (e.g., Zenith, Marvel-Schebler)
Engine Oil Change:
Every 50 operating hours or annually (refer to manual for specific interval and oil type).
Transmission Oil Change:
Every 200-300 operating hours or as specified in manual.
Greasing Points:
Daily or weekly depending on usage, lubrication schedule provided in manual.
Engine Oil Type:
API Service Classification SC/SD or SE, SAE 30W or 10W-30 (depending on ambient temperature). Manual will specify exact viscosity and API rating.
Transmission Fluid:
IH Hy-Tran Plus or equivalent tractor hydraulic fluid (TH F). Check manual for exact specification and capacity.
Coolant:
Permanent type antifreeze, 50/50 mix with water. Manual specifies type and capacity.
Carburetor Issues:
Clogging from sediment, needle valve sticking, leading to rough idling or flooding.
Hydraulic Lift Problems:
Slow operation or failure to lift due to worn hydraulic pump, cylinder seals, or low fluid level.
Electrical System Issues:
Corroded connections, faulty voltage regulator, worn starter brushes, leading to starting or charging problems.
Clutch Wear:
Slipping or difficulty engaging due to worn clutch disc or pressure plate.
