Engine Type:
Liquid-cooled inline 6-cylinder four-stroke diesel
Model Variant:
BF6M 1013 (including BF6M 1013E, BF6M 1013C and BF6M 1013FC variants where covered)
Production Years:
1990s through 2000s, exact range depends on variant
Application:
Industrial, agricultural and construction equipment plus generator drive applications
Target Audience:
Service technicians, fleet mechanics and experienced DIY owners
Market Position:
Deutz 1013 series is a widely used industrial diesel engine family in construction, agriculture and power generation equipment
Key Advantage:
Individual cylinder heads and wet liners make top-end service possible without removing the complete engine
Key Features:
Inline six-cylinder design, direct injection, optional turbocharging and charge-air cooling, mechanically governed or electronic injection pump depending on variant
Manual Type:
Workshop Service Repair Manual
Delivery Method:
Instant download after purchase
Page Count:
Depends on the supplied file - confirm at download
Coverage Areas:
Engine mechanical, fuel system, cooling, lubrication, electrical and adjustments
Engine Mechanical:
Cylinder head, valves, pistons, connecting rods, crankshaft, bearings, liners and block
Fuel System:
Injection pump, injectors, fuel lines, filters and governor
Cooling System:
Coolant pump, thermostat, radiator connections and belt drive
Lubrication System:
Oil pump, oil filter, oil cooler and pressure circuit
Electrical System:
Alternator, starter, sensors, wiring and charging circuit
Turbocharger:
Removal, inspection, installation and boost control where turbocharged
Disassembly:
Stepwise engine removal and strip-down sequence
Inspection:
Wear limits and component checking methods
Measurement:
Bore, valve clearance, bearing clearance and crankshaft end float
Reassembly:
Torque sequences and tightening values
Adjustments:
Valve clearance, injection timing and governor settings
Testing:
Compression testing, oil pressure testing and cooling system checks
Technical Depth and Parts
Technical Depth:
Component level with specifications, tolerances and service limits
Parts Information:
Component identification and part references where stated in the file
Wiring Diagrams:
Included where applicable to the electrical section
Troubleshooting:
Fault finding charts for starting, power loss, overheating and smoke complaints
Specifications:
Torque values, clearances and fluid capacities
File Format:
PDF (searchable, bookmarked, zoomable)
Compatibility:
Windows, macOS, Linux, iOS, and Android — any device with a PDF reader
Requirements:
A PDF reader application (e.g. Adobe Acrobat Reader, free)
Searchability:
Fully text searchable for fast lookup of any topic
Print Quality:
High-resolution digital pages, printable at full clarity
Binding Type:
N/A — digital download, no physical binding
Paper Type:
N/A — digital download, no physical paper
Configuration:
Inline 6-cylinder, four-stroke diesel
Displacement:
6.1 L class, exact value for specific variant in the manual
Bore and Stroke:
Confirm the exact figures from the specific model data in the manual
Aspiration:
Naturally aspirated, turbocharged and turbocharged with charge-air cooling depending on variant
Cooling:
Liquid-cooled with coolant pump and thermostat
Fuel System:
Direct injection via injection pump and injectors, mechanical or electronic governor depending on variant
Power Range:
Varies by variant and rating - consult the engine identification plate
Rated Speed:
Typical industrial ratings - confirm specific governed speed in the manual
Emissions:
Earlier variants mechanical, later variants may use electronic control as stated in the file
Standard Transmission:
N/A - engine only, transmission is supplied by the equipment manufacturer
Optional Transmission:
N/A - not a vehicle-specific powertrain; unit is coupled to the host machine
Coupling:
Flywheel housing and SAE bellhousing pattern used to mate to transmission or driven equipment
Note:
Clutch and gearbox service is not part of this engine manual unless stated in the file
Engine Layout:
Inline 6-cylinder, sump to top and front to rear as installed
Length, Width, Height:
Varies by variant, sump and flywheel housing fitted - confirm from the model data in the manual
Dry Weight:
Approximate by variant, does not include transmission or driven equipment
Mounting:
Engine mounts and brackets on the block and flywheel housing
Curb Weight Note:
N/A - vehicle curb weight is determined by the machine manufacturer, not the engine
Crash Test Ratings:
N/A - applies to vehicles, not to a standalone industrial engine
Active Features:
Engine protection shutdown, low oil pressure and high coolant temperature alarms as specified by the equipment manufacturer
Passive Features:
Guards and shields for belts, pulleys and turbocharger are supplied by the machine builder
Service Safety:
Isolate fuel, disconnect battery and allow engine to cool before work; follow the manual safety notes
Infotainment:
N/A - engine manual, no audio or infotainment system
Driver Assistance:
N/A - no vehicle driver assistance systems
Engine Control:
Mechanical injection pump on earlier variants, electronic control on later variants as covered in the manual
Monitoring:
Oil pressure, coolant temperature, charge pressure and speed sensors where fitted
Oil Change Interval:
Per equipment duty cycle - typically governed by the machine maker's schedule
Oil Specification:
API/ACEA heavy duty diesel oil of the viscosity grade stated for the ambient conditions in the manual
Coolant:
Ethylene glycol coolant mixed to the concentration specified for the local climate
Fuel Filters:
Replace at the intervals stated in the manual and after any fuel contamination event
Valve Clearance Check:
At the running hours stated in the manual, adjusted cold
Cooling:
Watch for coolant leaks at hoses, pump seals and cylinder head gaskets
Fuel System:
Injector and injection pump wear affects starting and smoke
Turbocharger:
Oil starvation or dirty oil shortens turbo life on turbocharged variants
Wear Items:
Belts, hoses, filters, injector nozzles and gaskets
